An automatic gate is two purchases that have to match: a gate built to take the load, and an operator sized to move it. Get the order wrong, pick the opener first and hang a gate off it, and you’ve got a machine working against itself for the rest of its life.

That’s most of what goes wrong with automated gates, and it’s all decided before anything gets installed. Call (512) 746-0980 or measure the opening with you, and we’ll start from what has to pass through it.

Get Free Estimate

What the decision actually commits you to

It’s worth being clear at the outset, because automation is often presented as an add-on, and it isn’t one. You’re committing to heavier posts, a power supply, safety equipment, and a mechanism that will need attention over its life. All of that’s fine, and it’s a different project from hanging a gate on hinges.

You’re also committing to what happens when it fails, because eventually it’ll fail. Every system needs a way to be released and moved by hand, and a way to get out if the power is off. Ask about both before you buy, not after.

Here’s Paul, who owns the company, on how we approach it:

Conditions can change even within the same property. That’s why we look at the actual site rather than assume a job will be straightforward just because we’ve worked nearby.

Paul, Owner, Ace Fence Company Austin

The gate comes first

Width, weight, and material get settled before an operator is chosen, because the operator has to be specified for what it’s actually moving. A wide iron gate and a light aluminum one of the same width require different drive systems.

Width’s the one people underestimate. Measure for the largest thing that has to pass, and measure for it turning rather than driving straight in, because a vehicle swinging through an opening needs more room than its own dimensions would suggest. Widening afterward means resetting both posts, which, on an automated gate, means redoing the mechanism as well.

The posts carry all of it. A gate post on a manual gate already takes a load no fence panel does, and an operator adds a machine pushing against it thousands of times a year. How gate posts get set matters more here than anywhere else on a property.

And the ground decides the posts. West and north of Austin, a hole digs cleanly for a foot and then meets caliche or limestone right where the depth is needed. We plan for that rather than meeting it on the day, and we won’t set a gate post short because the digging turned hard. On an automated gate, that shortcut isn’t a lean-in for four years; it’s a mechanism that stops lining up.

how-to-build-a-fence-gate-1.png
new wooden fence with gate

Swing or slide

Swing gates are the default, and they suit most driveways. They need a clear arc to open into, level ground through that arc, and enough room that a car waiting outside isn’t sitting where the gate wants to be.

Slide gates solve the cases swing gates can’t: a driveway that rises steeply from the road, an opening with no room to swing, or a gate wide enough that swinging it would be unwieldy. They need clear run-back space alongside the opening instead, which not every property has.

The choice is usually made by the site rather than by preference, which is why we’d rather stand on it than discuss it over the phone. Slope, drainage, and where water sits all feed into it, the same as they do on any fence on a graded lot.

Power and access

The operator needs power, and that’s the item most often discovered late. Getting supply to the gate can mean a trench from the house, which is a real cost and worth knowing before you commit rather than after the gate is built.

Then, how do you and everyone else get in? Remotes for the household, a keypad or intercom for visitors, and some way for deliveries and contractors to get through without you being home. Each of those is a decision, and they’re all easier to make before installation than to retrofit.

Backup power’s worth a thought too. Ask what happens in an outage, whether the gate fails open or closed, and how you release it manually. On a property where the gate is the only vehicle access point, that answer matters more than any feature in the specification.

Safety, which is not optional

A powered gate is a heavy moving object with real force behind it, and it moves whether or not something is in the way unless it’s told otherwise. That’s why safety devices exist: sensors that’ll stop or reverse the gate when something’s detected in its path.

Two standards govern this in the United States: UL 325 and ASTM F2200. We’re naming them because you should ask any installer how their system meets them, and because a contractor who can’t discuss them is telling you something. We’re not going to summarize what they require on a web page, since they’re detailed technical documents and a paraphrase from us would be worth less than the question you ask the person doing the work.

What we’d say plainly: if a quote for an automated gate doesn’t mention safety equipment at all, that’s the thing to ask about before you ask about price. It’s the one part of this project where what goes wrong involves a person rather than a fence.

Children and pets are the reason this matters more on residential property than on commercial property. Having a gate close on a car is expensive. A gate closing on something smaller isn’t the same category of problem.

What we will and won't do

We’ll build the gate, set the posts, and work with the operator system the job calls for. We’ll tell you what the ground’s likely to do before quoting, and we’ll say if we think the opening you have in mind is too narrow for what you’ve described passing through it.

What we won’t do is quote an automated gate without seeing the property. There’s the slope, the power run, the arc or the run-back, the ground, and the width, and you can’t see any of them from an address. We also won’t put an operator on a gate we don’t think is built to take it, which occasionally means recommending gate work before automation rather than alongside it.

If your existing gate’s been dragging or has stopped closing square, that’s a post problem, and it needs to be solved first. Putting a gate right before automating it is cheaper than automating and then discovering the post moves.

Where we install

Across the whole footprint: Austin, Cedar Park, Round Rock, Lakeway and Bee Cave, plus West Lake Hills, Steiner Ranch, Circle C Ranch, Barton Creek, Lost Creek, Northwest Hills, Great Hills and Old West Austin. Drive gates turn up most on the western and northern sides, where digging is hardest, so it’s where seeing the property matters most.

We’re fully insured, and our work carries a 1-year craftsmanship warranty. On an automated gate, that covers what we build and install rather than the operator manufacturer’s own terms, which is a distinction worth asking every contractor to spell out. What a fence project costs sets out the general shape, though a powered gate is priced separately.

Height and placement can also need approval, particularly along a road frontage, and what code caps a frontage at is worth settling before you commit to a design.

Your association may have a view too, and it usually does for a drive gate, since the gate is the most visible thing on the property from the street. What an association adds runs on its own calendar, so start it early. Call (512) 746-0980 or describe the driveway, and we’ll come take a look.

FAQs

More than most people expect, because it is several things at once: the gate, heavier posts, the operator, the power supply, safety equipment, and access controls. Getting power to the gate is the most often missed item. We quote the property based on the slope, the ground, and power run, all of which affect the price.

The site usually decides. Swing gates suit most driveways but need a clear arc, level ground through that arc, and room for a car to wait outside it. Slide gates suit steep driveways, openings with no room to swing, and very wide gates, but they need clear run-back space alongside.

Every system should have a manual release so the gate can be moved by hand, and some have battery backup. Ask whether the gate fails open or closed and how you release it, especially if it is your only vehicle access. It is a better question than most people ask about features.

They can be, and it depends entirely on the safety equipment and how it is set up. A powered gate moves with real force unless sensors tell it to stop or reverse. UL 325 and ASTM F2200 are the standards that govern this, and asking an installer how their system meets them is a reasonable question that a good one will answer readily.

Sometimes, and the honest answer depends on the gate and the posts. An operator adds a machine that pushes against a post thousands of times a year, so a post that already moves will move even more if your gate drags or has stopped closing square; that gets solved before automation, not after.

Wider than the largest thing that has to pass, with room for it to turn rather than just clear. Widening later means resetting both posts, and on an automated gate, it means redoing the mechanism as well, so it is much better to decide at the start.

It depends on height and where it sits, and a gate along a city right-of-way has its own requirements. Your association may also have a view on appearance and placement. Both are worth settling before you commit to a design rather than after.